fatrajah Posted January 20, 2016 Share Posted January 20, 2016 hiya, too true I couldn't word it better I asked for a tool change it was when he first started in the machine shop and he put the boring tools in the machine upside down, This is just idle curiousity on my part but I was wondering if George Toothill was the father of one of my junior school pals, Barry Toothill. I remember Barry's dad as being a serious, religious type who never smiled or talked to me; I always felt a bit uncomfortable in his presence. He would have been in his mid to late 30s in 1956/7. He used to get around on one of those push bikes with a little motor on the back axle. Link to comment Share on other sites More sharing options...
willybite Posted January 21, 2016 Share Posted January 21, 2016 This is just idle curiousity on my part but I was wondering if George Toothill was the father of one of my junior school pals, Barry Toothill. I remember Barry's dad as being a serious, religious type who never smiled or talked to me; I always felt a bit uncomfortable in his presence. He would have been in his mid to late 30s in 1956/7. He used to get around on one of those push bikes with a little motor on the back axle. hiya hard to say out side work he would walk past our house at the bottom of gleadless rd heeley as to where he lived i did not know he was a yes no man, ---------- Post added 21-01-2016 at 08:46 ---------- Hi Folks. I joined Laycocks in 1966 as a student apprentice, and stayed 'till 1974. The training centre was firmly run by Mr Lambert! I was top apprentice and won the Laycocks Prize. I studied for ONC at Granville College, and took a Degree at Bradford University. I won two National Awards for ONC. As an apprentice I worked in just about every department: Machining(OD & Clutch), Setting (OD J Type Annulus), Inspection (RR, Clutch, OD, GE, Foundry, Forge), Production Control (Clutch), Production Engineering (OD, Ford Crapi FF, US 'Spider' Gear Box), Overdrive/Clutch road testing and Problem Investigation, Foundry Labs, Forge, Tool Room (Clutch), etc., I worked in heat, cold, asbestos, cyanide salts, foundry dust, forge noise, test booth oil and noise combined! I have been covered in cutting oil, fingers full of gear shavings, wet through with soluble oil. You name it I seem to have been involved! After I graduated I was sent on Management Courses with GKN HQ Graduates and was made Manager of the Overdrive Refurbishment Dept. The Dept. was new, and I had to set it up from scratch. Before this ODs were refurbished in a shed on the car park. The reason it was needed was that David ?????, one of the directors, had piled literally thousands of service exchange units in stillages, and had had them hidden in an out of the way corner of the foundry. He had supplied new units in exchange!!!! None of the personnel who were assigned to me were trained in anything. In fact they were rejects from other depts. I did not want this. I did not want to waste my Engineering skills as a works manager. I wanted to work in design, but GKN/Laycocks would not listen, so I left. My experience is a good example of typical British Management philosophy: Hide what makes you look bad, even if it costs the company money. Don't try to do the job properly. Show no respect for Engineers. It's a sad shame that Laycocks went to the wall because of upper management ineptitude, but it's true of the rest of British Industry which has also collapsed! i hiya i read your letter with interest about the upper management,it always stuck in my gullet the way they worked,we had a change of manager by the way i worked in the clutch assembley, one time les hayles it was we thought great we have someone who knows the gripes on the shop floor, but alas they had him thinking the same as them, i remember one year at pay rise time we on the shop floor finished with £ 5 per week, then we heard afterwards the upper management gave themselves a £3,000. per year rise reason being there was less of them than us Link to comment Share on other sites More sharing options...
fatrajah Posted January 21, 2016 Share Posted January 21, 2016 (edited) Thanks for the reply, Willybite. The Toothills that I knew lived on Northcote Avenue which is near the top of Albert Road, so it could well have been the same bloke. Thanks again for the info. Edited January 22, 2016 by fatrajah Link to comment Share on other sites More sharing options...
Guest Posted July 5, 2016 Share Posted July 5, 2016 (edited) Sad to report the death of Brian Crookes aged 76 on Friday 1st July 2016. Brian was the Data Processing manager for many years and had also served on the Sports Club committee. Edited July 9, 2016 by Guest Link to comment Share on other sites More sharing options...
Rusta Posted December 4, 2018 Share Posted December 4, 2018 My Dad Raymond Clarke worked for Laycocks making clutches. Anyone remember him ? I Too remember the great Christmas parties ! Link to comment Share on other sites More sharing options...
trevjan Posted March 18, 2019 Share Posted March 18, 2019 My Farther Jack Forshaw worked at Laycocks for some 48 years both at Archer Road and Little London road on the overdrive section I have worked at two or three engineering companies and his name always seemed to be known. Link to comment Share on other sites More sharing options...
Saben Posted May 2, 2019 Share Posted May 2, 2019 Mr Forshaw used to continually walk around the section he was in charge of so he got thr nickname "Sputnic" after the Russian satelite! Link to comment Share on other sites More sharing options...
Mrs Kenno Posted February 3, 2020 Share Posted February 3, 2020 On 10/02/2014 at 15:51, 1959shaun said: Hi i worked with your dad for a few years, he was a lovely man bless him. He had Parkinsons then but always made light of it. I was at Laycocks approx 11 years up till around 1989 working on the plate line, my name is Shaun Goddard by the way. Thank you for your kind words Shaun. I don’t go on here much as you can tell from the dates! My dad was a lovely man and I’m blessed to be his daughter. Eleven years this week since he passed away and I still miss him every single day x Link to comment Share on other sites More sharing options...
Billam Posted February 3, 2020 Share Posted February 3, 2020 My brother, Christopher Billam worked there for a few years. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now